https://www.hse.gov.uk/pubns/mines06.pdf
http://www.ingr.co.uk/sar_construction.html
Thursday, 10 June 2021
Friday, 8 January 2021
Walks
fisheries loop, there are some footpaths across mynydd cerrig hill too
i like this route onto mynydd but follow the track as the footpath is very boggy
follow the track then take the first right footpath, the first right track leads to a house as does the track if you follow it all the way. Follow the middle footpath keep going up till u find the trig point
Wednesday, 16 December 2020
8 pin mini DIN
https://www.retrorgb.com/retro-gaming-cables-now-offering-8pin-minidin-scart-cables.html
https://etim.net.au/nesrgb/rgb_connector.htm
https://wiki.nottinghack.org.uk/wiki/Raspberry_Pi_Small_LCD
https://www.amazon.ca/Component-Video-Audio-Output-Adapter/dp/B071NLCZDB
Tuesday, 18 October 2016
PB G3/3400 power plug
from http://pinoutsguide.com/Power/apple_tibookpower_pinout.shtml
Works without the internal LEDs or the outer sleeve. The basis of the connector is a 2.5mm (yes 2.5mm, not 3.5mm) male jack. Functioning 100%, including charging the battery.
Only numbers are taking in account at drawing.
Correction for Powerbook G3 and Clamshell Notebook (3.5 mm jack): Tip (1 = front-most connector) is _NOT_ connected. Ring (2 = middle connector) is the common lead (minus polarity). The sleeve (3) is connected to +24V, this is the inner (hot) wire (with white insulation) of the original G3 (yo-yo type) power adaptor.
Also there is a supply for the loading indicator LED _within_ the plug. A resistor from +24V to the outer 9.5mm tube around the power plug.
Also Suitable for iBook G3 iBook G4 PowerBook G4
NB:PowerBook G3 and iBook Clamshell Require 3.5mm Jack
Basic version of Apple power connectorWorks without the internal LEDs or the outer sleeve. The basis of the connector is a 2.5mm (yes 2.5mm, not 3.5mm) male jack. Functioning 100%, including charging the battery.
| power adapter cable Pin |
Name | Direction | Description |
|---|---|---|---|
| 1 (left) | sense | 400KOhm to GND | |
| 2 (right) | GND | Ground | |
| 3 (ground) | Vin | <-- td=""> | +24V power |
Only numbers are taking in account at drawing.
Correction for Powerbook G3 and Clamshell Notebook (3.5 mm jack): Tip (1 = front-most connector) is _NOT_ connected. Ring (2 = middle connector) is the common lead (minus polarity). The sleeve (3) is connected to +24V, this is the inner (hot) wire (with white insulation) of the original G3 (yo-yo type) power adaptor.
Also there is a supply for the loading indicator LED _within_ the plug. A resistor from +24V to the outer 9.5mm tube around the power plug.
Monday, 12 October 2015
Made mainly using Wills materials, with coarse stone walls and corrugated iron roof sheets. Dornaplas windows - Glazed.
Structure is fully painted and weathered, ready to place on your layout.
(Loco shown in photos is for scale purposes only - not included)
Dimensions: Whole building at widest points: approx 140mm long x 120mm wide
Main shed: 125mm long x 82mm wide (internal).
Office lean to: 53mm x 35mm
Door: 32mm wide x 47mm high.
http://www.ebay.co.uk/itm/ENGINE-SHED-AND-WORKSHOP-009-SCALE-/301762407470?hash=item464270ec2e
Monday, 5 October 2015
U-20
files
http://www.synthzone.com/midi/roland/u20/
Roland U-20 Initializing – Restoring the Factory Settings
The following procedure can be used to clear the internal memory and reload some of the factory settings:
(CAUTION: All USER information will be lost. Be sure to back up any information you wish to keep.)
Original factory data for the U-20 must be loaded in via MIDI or a memory card. There is, however, a memory clearing function that returns most of the other parameters to their original factory settings. Use the following procedure to initialize the U-20:
1. Press PART and RHYTHM simultaneously to enter ROM play mode.
2. While holding MARK and JUMP, press ENTER to enter Test mode.
3. While holding JUMP, press NUMBER 7.
4. Press ENTER.
5. Press VALUE [^] to confirm.
6. While holding MARK and JUMP, press EXIT to exit Test mode.
Note: See “Loading System Exclusive Data” for the procedure to load the factory data through MIDI.
(CAUTION: All USER information will be lost. Be sure to back up any information you wish to keep.)
Original factory data for the U-20 must be loaded in via MIDI or a memory card. There is, however, a memory clearing function that returns most of the other parameters to their original factory settings. Use the following procedure to initialize the U-20:
1. Press PART and RHYTHM simultaneously to enter ROM play mode.
2. While holding MARK and JUMP, press ENTER to enter Test mode.
3. While holding JUMP, press NUMBER 7.
4. Press ENTER.
5. Press VALUE [^] to confirm.
6. While holding MARK and JUMP, press EXIT to exit Test mode.
Note: See “Loading System Exclusive Data” for the procedure to load the factory data through MIDI.
Roland U-20 Loading System Exclusive Data
Many MIDI devices allow you to store and retrieve data via MIDI
system exclusive messages. For example, all the factory settings can be
loaded back into the U-20 using this method. Use the following procedure
to setup the U-20 to receive system exclusive data:
1. Press EDIT.
2. CURSOR to “Setup” and press ENTER.
3. CURSOR to “MIDI” and press ENTER.
4. CURSOR to “Common” and press ENTER.
5. CURSOR to “RX SysEx =” and use the VALUE buttons to select “On.”
6. CURSOR to “SysEx Device ID = “ and use the VALUE buttons to choose “17.”
7. Press KEYBOARD and SOUND simultaneously and then begin sending the MIDI system exclusive data from your sequencer.
http://www.sysexdb.com/synth_detail.aspx?dv=92
1. Press EDIT.
2. CURSOR to “Setup” and press ENTER.
3. CURSOR to “MIDI” and press ENTER.
4. CURSOR to “Common” and press ENTER.
5. CURSOR to “RX SysEx =” and use the VALUE buttons to select “On.”
6. CURSOR to “SysEx Device ID = “ and use the VALUE buttons to choose “17.”
7. Press KEYBOARD and SOUND simultaneously and then begin sending the MIDI system exclusive data from your sequencer.
http://www.sysexdb.com/synth_detail.aspx?dv=92
Friday, 18 September 2015
Subscribe to:
Posts (Atom)